Dry Ice Blasting Mold

Cryogenic mold removal that kills spores without water or chemicals

Dry Ice Blasting Mold in VAN NUYS, California Done Right

Dry Ice Blasting Mold in VAN NUYS, California is the fastest way to strip mold off framing, ducts, and crawl space joists without soaking your structure. We blast frozen CO2 pellets at supersonic speed, lift the growth off the wood, and leave nothing behind but a dry surface ready for encapsulation. If you have black mold growth, musty odors, or water damage mold in your home or commercial building, call us at (833) 929-5837.

Live phone supportUpfront optionsBacked workmanship
Call firstLive triage can help before arrival
Safety before speedRisks assessed before work begins
Diagnose the causeWe trace the source, not just the symptom
Approve the workScope and price explained upfront

What's included

What Our Dry Ice Blasting Mold Service Includes

Every job includes the full scope from inspection to clearance testing. We do not nickel-and-dime you for containment or HEPA vacuuming, and we do not leave until the lab confirms the job worked. Here is exactly what you get when you book dry ice blasting mold in VAN NUYS California.

01

Full Moisture & Thermal Inspection

We map every wet pocket with a moisture meter and thermal imaging camera, then check wall cavities and duct runs with a boroscope inspection camera. You get a written scope with photos before we set up containment. Most inspections take 60 to 90 minutes.

02

Containment & Negative Air

We build a 6-mil plastic containment sheeting barrier and run a negative air machine with HEPA filters. This keeps spores from drifting into the rest of your home. Crew members wear disposable coveralls and respirator cartridges during the entire blast.

03

Dry Ice Blasting & HEPA Vacuuming

Our technician blasts the affected framing, sheathing, and ductwork with 3mm dry ice pellets, then vacuums every surface with a HEPA vacuum. A typical crawl space takes 2 to 4 hours; a full attic takes 4 to 6. No water, no chemical residue, no secondary cleanup.

04

Mold Encapsulant Application

We apply a mold encapsulant such as Fiberlock or Concrobium to lock down any root structure the blast did not lift. This is the step that prevents post-remediation mold recurrence. It goes on after the HEPA vacuum, not before, so it bonds to a clean surface.

05

Odor Treatment & Air Scrubbing

If the space had heavy musty odors, we run an ozone generator or a fogger with Benefect for 4 to 8 hours. An air scrubber runs at 500 CFM throughout the job to keep airborne spore counts down. You come back to a space that smells like nothing.

06

Clearance Testing & Lab Report

We collect air samples and surface swabs after the job and send them to an accredited lab. Results come back in 24 to 48 hours. If spore counts are not back to outdoor baseline, we re-blast at no extra charge. That is the ANSI/IICRC S520 standard.

Service overview

Dry Ice Blasting Mold in VAN NUYS, California

Dry Ice Blasting Mold in VAN NUYS, California is a dry remediation method that uses compressed air to fire rice-sized dry ice pellets at 300 to 1,500 feet per second. The pellets hit the mold at roughly -109 degrees Fahrenheit, freeze it, and the kinetic impact lifts it off the substrate. Because the dry ice sublimates on contact, there is no secondary blast media to sweep up, no water to dry, and no chemical residue left on your framing. It is the same technology used to clean industrial molds and food-processing lines, adapted here for structural mold removal.

Most VAN NUYS homes we walk into have the same story: a slow supply-line leak behind the vanity, a roof flashing that failed during last winter's rain, or a crawl space that never dried out after the Sepulveda Basin flooding. By the time you smell the musty odor, mold has already colonized the back of the drywall and the top plate. If you have been searching for dry ice blasting mold in VAN NUYS California near me, our IICRC-certified crews handle the inspection, containment, blasting, and post-remediation verification in one visit.

No Water, No Secondary DamageTraditional pressure washing and chemical washing push water into the same wood you are trying to dry. Dry ice blasting mold removal in VAN NUYS leaves the substrate bone dry, so you skip the 3-5 day drying cycle and the risk of new mold growth in the same cavity.
Zero Chemical ResidueWe use no bleach, no quaternary ammonia, and no antimicrobial fog on the blasted surface. That matters in occupied homes, schools, and food-handling spaces. If you need dry ice blasting mold with no chemical residue in VAN NUYS, this is the process that delivers it.
Reaches What Brushing Can'tWire brushing and sanding cannot get behind nail heads, into 2x4 end grain, or inside HVAC plenum seams. The CO2 stream reaches those pockets in seconds. On a typical 1,200 sq ft attic, our crew clears 90 percent of visible growth in under four hours.
Dry Ice Blasting Mold by Mold Remediation Service Van Nuys
How we workWe verify the cause, compare realistic options, and confirm the repair before we leave.

The service timeline

Our Dry Ice Blasting Mold Process

The process flexes to the condition, but these checkpoints keep decisions clear.

01

Inspection & Mapping

We start with a moisture meter and a thermal imaging camera to find every wet pocket, not just the visible stain. A boroscope inspection camera goes into wall cavities and duct runs. You get a written scope with photos before we set up a single containment barrier. Most inspections take 60 to 90 minutes.

Stage 1
02

Containment Setup

We build a 6-mil plastic containment sheeting barrier around the work zone and install a negative air machine with HEPA filters. This keeps spores from drifting into the rest of your house. Crew members suit up in disposable coveralls and respirator cartridges before any blasting begins.

Stage 2
03

Dry Ice Blasting

Our technician loads the dry ice blasting machine with 3mm pellets and works the surface in overlapping passes. A typical crawl space takes 2 to 4 hours; a full attic takes 4 to 6. The mold lifts off the wood and the pellets vanish into thin air, leaving only dry debris for the HEPA vacuum.

Stage 3
04

HEPA Vacuum & Antimicrobial

We vacuum every blasted surface with a HEPA vacuum, then apply a mold encapsulant such as Fiberlock or Concrobium to lock down any remaining root structure. If the space had heavy odor, we run an ozone generator or a fogger with Benefect for 4 to 8 hours after the crew leaves.

Stage 4
05

Clearance Testing

We take air samples and surface swabs, then send them to an accredited lab. You get the results in 24 to 48 hours. If spore counts are not back to outdoor baseline, we re-blast at no extra charge. That is the ANSI/IICRC S520 standard we hold ourselves to.

Stage 5

Tools & methods

Tools & Methods We Use on Every Job

Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.

01

Dry Ice Blasting Machine

Fires 3mm dry ice pellets at 300 to 1,500 feet per second. This is the core tool that lifts mold off framing without water or abrasive media.

02

Thermal Imaging Camera

Finds temperature differences that reveal hidden moisture pockets behind walls and under floors. We use it before we set containment so the scope is accurate.

03

Moisture Meter

Confirms wet readings on wood, drywall, and concrete. We take readings before and after the job to prove the structure is dry enough for encapsulation.

04

Boroscope Inspection Camera

Slides into wall cavities and duct runs to see growth without tearing out drywall. Essential for confirming mold on framing before we commit to blasting.

05

HEPA Vacuum & Air Scrubber

The HEPA vacuum pulls blasted debris off surfaces, and the air scrubber runs at 500 CFM to keep airborne spore counts down during the job.

06

Negative Air Machine

Maintains negative pressure inside containment so spores cannot drift into the rest of the home. Runs the entire job, from setup to teardown.

07

Ozone Generator & Fogger

Neutralizes musty odors in porous framing and duct lining after the blast. We use Benefect or Concrobium in the fogger for a low-odor, plant-based finish.

Use cases

When to Call for Dry Ice Blasting Mold

These examples show how the service framework adapts rather than forcing every call through one repair.

Dry Ice Blasting Mold
1950s Crawl Space Joist RestorationA 1,400 sq ft home in Van Nuys Central had black mold growth across 60 percent of the crawl space joists after a slow slab leak. Moisture meter readings were 28 percent on multiple joists, and the musty odor was noticeable in the living room. → We contained the crawl space, blasted the joists and subfloor with dry ice, HEPA vacuumed, and applied encapsulant. Post-job moisture readings dropped to 11 percent. Lab clearance came back at outdoor baseline 48 hours later. Original 1950s framing was saved.

Restaurant Ductwork Mold Removal

A restaurant on the Van Nuys Boulevard Corridor had visible mold in the walk-in cooler framing and the supply duct above the prep line. Air samples showed spore counts 4x outdoor baseline. The owner could not afford to close for a multi-day remediation. → We ran an overnight job: contained the work zone, blasted the cooler framing and duct interior, HEPA vacuumed, and applied encapsulant. Post-job air samples came back at baseline. The restaurant opened on time the next morning and passed its health inspection.

Attic Sheathing After Roof Leak

A Lake Balboa homeowner found black mold growth on attic sheathing after a roof flashing failure during last winter's storms. About 200 sq ft of sheathing was affected, and the insulation below was starting to smell musty. → We inspected with a boroscope inspection camera, confirmed the leak path, blasted the sheathing and rafters, and HEPA vacuumed the space. Insulation tested clean and was left in place. The whole job finished in one day. Clearance testing passed 24 hours later.

Problems we solve

Mold Problems We Solve in VAN NUYS

Most VAN NUYS mold calls fall into a handful of patterns. Here are the ones we see most, what happens if you ignore them, and how dry ice blasting mold in VAN NUYS California fixes them.

ISSUE

Black mold growth on crawl space joists

We contain the crawl space, blast the joists and subfloor with dry ice, HEPA vacuum the debris, and apply a mold encapsulant. A typical 1,500 sq ft crawl space takes 3 to 4 hours of blasting and finishes the same day.

SYMPTOM

Attic mold on sheathing after a roof leak

We inspect with a thermal imaging camera to find the leak source, blast the sheathing and rafters, then HEPA vacuum the space. If insulation is clean, we leave it in place. Most attic jobs finish in 4 to 6 hours.

SIGN

HVAC mold contamination in ductwork

We isolate the duct run, blast the interior metal with dry ice, and HEPA vacuum the plenum. Duct board that is too far gone gets removed and replaced. We finish with an antimicrobial fog and a post-remediation mold testing pass.

ALERT

Water damage mold after a supply-line leak

We dry the structure first with a dehumidifier and air mover, then blast any mold that colonized during the wet period. This is the most common water damage mold remediation call we run in VAN NUYS. Skipping the dry-out is the top cause of recurrence.

Pricing process

Dry Ice Blasting Mold Pricing in VAN NUYS

$1,800 - $4,200 residential; $2.50 - $5.00 per sq ft commercial

Phase 01

Square footage affected

The single biggest driver. A 200 sq ft attic job runs $1,800 to $2,400. A 1,500 sq ft crawl space runs $2,800 to $4,200. Commercial pricing is per square foot, usually $2.50 to $5.00.

Phase 02

Access and containment difficulty

A crawl space with a 24-inch access hatch takes longer to contain and work than an open attic. Tight access adds labor hours, and that shows up in the quote. We tell you upfront if access is going to move the number.

Phase 03

Material removal vs. blasting

Dry ice blasting saves framing, but contaminated insulation, duct board, and finished drywall still have to be removed and replaced. The more material that has to go, the higher the job cost.

Questions before we arrive

Frequently Asked Questions About Dry Ice Blasting Mold

Dry Ice Blasting Mold
Call (833) 929-5837
How much does dry ice blasting mold cost in VAN NUYS California?

Most residential jobs run $1,800 to $4,200 in 2026, depending on square footage and access. A single bathroom or small attic averages $1,800 to $2,400. A full crawl space under a 1,500 sq ft home runs $2,800 to $4,200. Commercial buildings price per square foot, usually $2.50 to $5.00. That range includes containment, blasting, HEPA vacuuming, encapsulant, and clearance testing.

Is dry ice blasting safe for mold removal in VAN NUYS?

Yes, when the work zone is contained and the crew wears proper PPE. The CO2 is food-grade and leaves no toxic residue, so it is safe around kids, pets, and food-prep areas once we clear the space. The one real hazard is oxygen displacement in tight crawl spaces, which is why we run continuous air monitoring and never blast a confined space without ventilation. We follow ANSI/IICRC S520 throughout.

How does dry ice blasting remove mold in VAN NUYS California?

Three forces work at once. The pellets hit at -109 degrees Fahrenheit and freeze the mold, the kinetic impact fractures the cell structure, and the rapid sublimation lifts the debris off the wood. There is no water and no abrasive media, so the wood grain stays intact. We then HEPA vacuum the surface and apply a mold encapsulant to seal any remaining root structure.

What surfaces can be dry ice blasted in VAN NUYS California?

We blast dimensional lumber, plywood sheathing, OSB, concrete, brick, metal ductwork, and most HVAC components. It is the best option for structural framing in VAN NUYS because it reaches nail heads, end grain, and plenum seams that brushing cannot. We do not blast soft plastics, vinyl siding, or finished drywall, since the pellet stream can pit those surfaces. Those get removed and replaced instead.

Ready when you are

Book Dry Ice Blasting Mold in VAN NUYS, California

One call gets you a same-day inspection, a flat-rate written price, and a crew that shows up when we say we will. We are licensed, insured, and IICRC certified. Call (833) 929-5837 now and let us get the mold off your framing before it spreads.

Dry Ice Blasting Mold

Talk with the local team

Request Dry Ice Blasting Mold

Call us any time at (833) 929-5837. We answer 24/7, including holidays, and dispatch same-day across Van Nuys and the San Fernando Valley. If you prefer email, send us a message and we'll respond within a few hours during business hours.

6801 1/2 Woodman Ave, Van Nuys, CA 91405, USA, VAN NUYS, CaliforniaMain office · technicians serve the full area

Thanks — your request is in. We will contact you shortly.

Call now