
Thermal imaging, moisture meters, and lab-backed answers for your home
Home Mold Inspection in VAN NUYS, California
A Home Mold Inspection in VAN NUYS, California is the fastest way to find out whether that musty smell, ceiling stain, or crawl space discoloration is active mold growth. We inspect attics, bathrooms, basements, and HVAC systems across the San Fernando Valley, document what we find with photos and moisture readings, and hand you a clear report you can act on. If you have been searching for a residential mold assessment in VAN NUYS California, we can usually get eyes on the problem this week.
What's included
What Is Included in the Inspection
Every Home Mold Inspection in VAN NUYS, California includes the core scope below. Lab sampling is added when we find suspect growth, and remediation is quoted separately if it is needed. You get the full price before we schedule, and the written report is delivered within 24 hours of the site visit.
Full Visual Walkthrough
Every room, closet, cabinet, and utility space gets inspected. We check under sinks, behind appliances, around water heaters, and inside the HVAC closet. Exterior walls, roof penetrations, and grading get reviewed for water intrusion paths that feed indoor growth.
Moisture Meter Readings
We take point readings on drywall, framing, subfloor, and baseboards throughout the home. Readings above 16 percent on wood or 1 percent on drywall signal elevated moisture. You get the numbers in the report, not just a verbal summary.
Thermal Imaging Scan
A thermal imaging camera shows temperature differences that reveal hidden moisture behind finished surfaces. We scan every exterior wall, the ceiling plane, and around every plumbing fixture. This is how we find leaks that have not yet stained the drywall.
Attic and Crawl Space Inspection
We climb into the attic and crawl space with a boroscope inspection camera when access is tight. Roof sheathing, rafters, insulation, and duct runs get checked for staining and microbial growth. Crawl space joists and vapor barriers get the same treatment.
HVAC System Check
The air handler, return plenum, and accessible duct runs get inspected for HVAC mold contamination. This is one of the most overlooked sources of musty air in Valley homes, especially when the system has been running through a wet winter without a filter change.
Written Report with Photos
Your report includes photos of every finding, moisture readings, thermal images, lab results if samples were collected, a mold map, and a recommended scope of work. It is formatted so you can hand it to an insurer, a buyer, or a remediation crew without translation.
Service overview
What a Home Mold Inspection in VAN NUYS, California Covers
A Home Mold Inspection in VAN NUYS, California is a room-by-room evaluation of your house for active mold growth, hidden moisture, and the conditions that feed both. We start with a moisture meter and thermal imaging camera to scan walls, ceilings, and floors for temperature swings that signal trapped water. Then we check the usual suspects: attic sheathing, crawl space joists, bathroom caulk lines, under-sink cabinets, and the air handler. When we find something, we document it with photos and readings so you know exactly where it is and how big it is.
Van Nuys homes deal with a specific set of mold triggers. Summer attic temperatures push past 140 degrees, then winter rain and Santa Ana wind cycles drive water into 1950s stucco and flat roofs. Add decades-old galvanized plumbing and slab leaks, and you get crawl space mold and bathroom mold that spreads quietly for months. If you have been putting off a house mold inspection VAN NUYS homeowners trust, the cost of waiting is usually a bigger remediation bill. We also serve nearby Valley Glen and Lake Balboa with the same inspection protocol.
The service timeline
How Our Inspection Process Works
The process flexes to the condition, but these checkpoints keep decisions clear.
Phone Intake
We ask about the smell, any visible staining, recent water events, and the age of the home. That call takes 10 to 15 minutes and lets us load the right equipment. If you have a slab leak history or a recent roof repair, tell us, because those change where we look first.
Visual Walkthrough
We start outside and work in. Roof penetrations, stucco cracks, window flashing, and grading get checked first, then we move through every room. Bathrooms, kitchens, laundry closets, and the water heater pan get close attention. We photograph anything that looks like past or present water intrusion.
Moisture and Thermal Scan
A moisture meter gives us point readings on drywall, framing, and subfloor. A thermal imaging camera shows us the temperature differences that reveal hidden moisture behind finished surfaces. We scan every exterior wall, the ceiling plane, and around every plumbing fixture. This is where most hidden problems get caught.
Attic, Crawl Space, HVAC
We climb into the attic and crawl space with a boroscope inspection camera when access is tight. Roof sheathing, rafters, insulation, and duct runs get checked for staining and microbial growth. The air handler and return plenum get inspected for HVAC mold contamination, which is one of the most overlooked sources of musty air in Valley homes.
Samples and Report
If we find suspect growth, we collect surface samples or air samples for lab analysis. Results come back in 24 to 72 hours depending on the lab. Your written report includes photos, moisture readings, lab results, a mold map, and a recommended scope of work with pricing if remediation is needed.
Tools & methods
Tools and Methods We Use
Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.
Moisture Meter
Point readings on drywall, framing, subfloor, and baseboards. Readings above 16 percent on wood signal elevated moisture and a likely mold source.
Thermal Imaging Camera
Reveals temperature differences behind finished surfaces that indicate hidden moisture. Used on every exterior wall, ceiling plane, and plumbing fixture.
Boroscope Inspection Camera
Lets us see inside wall cavities, duct runs, and tight attic spaces without cutting access holes. Essential for confirming growth in concealed areas.
HEPA Vacuum
Captures mold spores and debris during remediation without releasing them back into the air. Used with HEPA filters rated for fine particulate.
Air Scrubber and Negative Air Machine
Maintains negative pressure inside containment so spores do not migrate to clean areas of the home during removal work.
Dehumidifier
Pulls moisture out of the air and structural materials after a water event. Dri-Eaz and Phoenix Restoration units are our standard equipment.
Dry Ice Blasting Machine
Lifts mold off framing and sheathing using compressed dry ice pellets. No water, no abrasive media, no residue left behind.
Use cases
When to Book a Home Mold Inspection
These examples show how the service framework adapts rather than forcing every call through one repair.

Crawl Space Mold After Winter Rain
A Lake Balboa home with a raised foundation had a musty smell in the living room that got worse every winter. The crawl space had no working vapor barrier, and floor joists showed visible growth along the north side. Moisture readings on the joists were 24 to 28 percent. → We removed affected insulation, treated the joists with antimicrobial solution, and installed a new vapor barrier. Post-remediation moisture readings dropped to 12 to 14 percent. Air samples confirmed spore counts back at baseline, and the smell in the living room cleared.
Bathroom Mold From Slow Supply Leak
A Van Nuys Central homeowner had recurring mold around the base of the vanity that came back every few months despite regular cleaning. Our moisture meter found 31 percent moisture in the drywall behind the vanity, and a thermal scan showed a slow supply line leak inside the wall cavity. → We scoped removal of the affected drywall, treated the framing with antimicrobial solution, and the homeowner had a plumber replace the failing supply line. Post-remediation air samples were clean, and the growth has not returned.
Problems we solve
Problems Our Inspection Solves for Van Nuys Homes
Most mold calls start with a smell, a stain, or a health symptom that does not have an obvious cause. Here are the problems we run into most often in Van Nuys, and how we solve them.
Musty odor with no visible growth
We use a thermal imaging camera and moisture meter to trace the smell to its source, then collect air samples to confirm elevated spore counts. Once we map the source, we scope the fix and the remediation in one report.
Attic staining after a roof leak
We inspect the attic with a boroscope inspection camera, take moisture readings on the sheathing, and sample any suspect growth. If remediation is needed, we scope dry ice blasting or HEPA vacuuming plus antimicrobial treatment.
Crawl space mold after winter rain
We inspect the crawl space, check the vapor barrier, and measure moisture on joists and subfloor. Remediation includes removal of affected insulation, antimicrobial treatment of framing, and correction of the moisture source so growth does not return next season.
Bathroom mold that keeps coming back
We trace the moisture with a meter, check supply lines and drain connections, and identify whether the source is a leak, a ventilation problem, or both. Then we scope remediation and the fix that stops it from returning.
Pricing process
Home Mold Inspection Pricing in Van Nuys
$250 - $650 for a standard inspection; $75 - $150 per lab sample
Square footage
A 1,200 square foot Van Nuys ranch takes about two hours to inspect. A 3,000 square foot home with multiple attics and a large crawl space can take four hours or more, which raises the inspection fee.
Attic and crawl access
Homes with tight scuttle access or no crawl space access panel require more time and sometimes a boroscope survey. We tell you upfront if access is going to affect the price.
Number of lab samples
Air samples and surface samples run $75 to $150 each at the lab. A basic inspection might need one or two. A larger home with multiple suspect areas might need four or more.
How much does home mold inspection cost in VAN NUYS California?
Most residential inspections in Van Nuys run $250 to $650 in 2026, depending on square footage, attic and crawl space access, and how many lab samples you need. A basic visual and moisture inspection with one or two air samples sits at the low end. Larger homes, or inspections that require multiple surface samples and a boroscope survey, land at the higher end. You get the full price before we schedule.
What does a home mold inspection include in VAN NUYS?
A standard inspection includes a full visual walkthrough, moisture meter readings on every exterior wall and plumbing fixture, thermal imaging of ceilings and walls, attic and crawl space inspection, HVAC air handler check, and a written report with photos. Lab sampling for air or surface mold is added when we find suspect growth. Most homes take two to four hours on site.
How often should I get home mold inspection in VAN NUYS California?
Every two to three years for a healthy home, and immediately after any water event. That means a slab leak, a roof leak, a water heater failure, an AC condensate overflow, or any flooding. Van Nuys homes also benefit from an inspection before each rainy season, since winter storms are when most hidden intrusion shows up. If you smell musty air, do not wait for the calendar.
Can I do my own home mold inspection in VAN NUYS California?
You can spot visible growth and smell musty odors, but you cannot read moisture behind drywall or identify species without a meter, a thermal camera, and a lab. DIY kits sold online often give false negatives because they miss hidden sources. If you suspect mold, a professional inspection costs less than a single remediation job and gives you documentation you can actually use.
Ready when you are
Book Your Home Mold Inspection in VAN NUYS, California
If you smell musty air, see staining on a ceiling, or just closed on a house with a crawl space you have never looked inside, get it inspected. We are IICRC certified, EPA Lead-Safe certified, and we document everything. Call (833) 929-5837 and we will get you on the schedule this week.

Talk with the local team
Request Home Mold Inspection
Call us any time at (833) 929-5837. We answer 24/7, including holidays, and dispatch same-day across Van Nuys and the San Fernando Valley. If you prefer email, send us a message and we'll respond within a few hours during business hours.



